Humpday | Grace Technologies Blog

Why MCC and PDU Connections Fail Hot First and How to Catch It Early

Written by Alyssa Rice | Nov 18, 2026, 7:30:00 PM

Common MCC overheating causes include thermal cycling, vibration, and improper torque, all of which can weaken a bolted connection and increase its electrical resistance. As current flows through the joint, that extra resistance creates a hot spot. The same process can occur in a power distribution unit (PDU), where heat can build long before the connection fails.

What Are the Main MCC Overheating Causes?

Connections in a motor control center (MCC) overheat when reduced contact pressure or deteriorating contact surfaces increase resistance at the joint. A motor can still be running normally while a lug or bus joint inside the MCC heats up.

  1. Thermal cycling. As loads change, repeated expansion and contraction can reduce pressure at the joint.
  2. Vibration. Motors, starters, and nearby machinery can transmit vibration to connections, which can contribute to loosening over time.
  3. Incorrect torque. A connection tightened outside the manufacturer’s specifications during installation or after maintenance may have poor contact or suffer damage.
  4. Corrosion and oxidation. Buildup on contact surfaces can increase resistance even when the connection looks secure from the outside.
  5. Conductor creep. A conductor can slowly deform under sustained pressure. This is especially relevant to aluminum, where that movement can reduce pressure at the termination.
  6. Undersized or damaged lugs. A lug that’s damaged or sized incorrectly for the conductor can reduce effective contact area and concentrate heat.

More resistance creates more heat at the same current, and repeated heating can further weaken the connection. That’s why loose connections are one of the common causes of electrical overheating.

Why Do PDU and RPP Connections Fail in Data Centers?

PDU overheating in a data center can start at a deteriorating connection that carries a heavy load for long periods. The same can happen in a remote power panel (RPP), where a breaker connection or cable termination can develop a hot spot while the panel continues to supply power.

In dense cabinets with limited airflow, the surrounding temperature can also affect readings. Comparing similar connections under similar loads helps teams tell whether one joint is heating more than its neighbors.

Redundant power paths help a data center stay online, but taking a unit out of service still takes coordination. A rising temperature can help teams prioritize what to investigate when a maintenance window opens.

 

What Does an IR Scan Miss?

An infrared (IR) scan can miss a hot spot that develops between inspections or that runs cooler under a lighter load. A connection that looks normal on a light production day may run hotter once the line returns to its usual load. If it starts to deteriorate after a quarterly or annual scan, the next scan may be months away.

An IR camera also needs a clear view of the surface being measured. Doors, covers, and internal barriers can block that view, while an IR window provides access to the points visible through it. If the inspection involves exposure to energized parts, qualified personnel follow the applicable electrical safety procedures and use the PPE called for by the hazard assessment.

An IR scan is a snapshot. Monitoring is the film. A series of readings can show when the temperature started rising and whether that trend holds under similar loads.

How Do You Catch a Hot Connection Early?

Continuous thermal monitoring uses permanently installed sensors to track temperatures at selected electrical connections while equipment operates. If you’re trying to detect loose connections in switchgear, an upward temperature trend can point to a joint that needs investigation. Qualified personnel can use load and inspection data to determine the cause.

The GraceSense HSM 600 provides continuous thermal monitoring for low-voltage equipment rated up to 600 VAC. Thermistor sensors measure temperatures on or near selected points such as bus joints, lugs, and cable terminations. Teams can follow temperature trends with the doors closed and receive alerts when readings cross configured thresholds.

For example, if an MCC feeder lug runs warmer each week at about the same load, your team has a specific connection to investigate.

What to compare IR thermography Continuous thermal monitoring
What it measures Surface temperatures within the camera’s line of sight Temperatures at points equipped with sensors
How often it measures During scheduled or on-demand inspections Continuously during operation
Enclosure access Doors or covers may need to be opened for line of sight. An IR window can provide a view of accessible points with the door closed. Doors can stay closed for routine readings once sensors are installed.
PPE Depends on the task and applicable hazard assessment, including exposure to energized parts. Remote readings can be reviewed away from the equipment. Installation and service follow applicable electrical safety procedures.

What Should You Check First?

Start with the assets where a single connection failure would have the greatest effect on safety, production, or uptime.

  • Identify critical assets. List the MCCs, PDUs, RPPs, and switchgear you’d prioritize if a connection started to run hot.
  • Review past IR reports. Look for recurring hot spots and note any critical joints that are difficult to see during a scan.
  • Check the outage schedule. Identify the next planned maintenance window and confirm installation requirements with your electrical team.
  • Plan for data and alerts. Decide where readings will go, who will receive alerts, and who will coordinate the response.

The CTM Readiness Checklist walks you through these decisions, along with network readiness, team training, and recordkeeping.

What Else Should You Know About Electrical Connection Overheating?

The load, the reference temperature, and how you collect readings all affect how you interpret a hot spot.

What Temperature Is Too Hot for an Electrical Connection?

The threshold depends on the reference temperature. The NETA temperature guidelines flag a rise of 4 to 15°C over a similar component under similar load as a probable deficiency. A rise above 15°C calls for immediate repair. See how hot is too hot for an electrical connection for the separate thresholds used when comparing against ambient temperature.

How Often Should MCCs Be Scanned Under NFPA 70B?

Where periodic thermography is used, NFPA 70B generally calls for annual scans, with shorter intervals for equipment in poorer condition. Check the applicable edition and your electrical maintenance program for the interval that applies to your MCCs. For more on the current edition, see the NFPA 70B maintenance requirements.

What Causes a Loose Lug or Connection?

Thermal cycling, vibration, incorrect torque, and conductor creep can reduce pressure at a lug or bolted joint. Corrosion can also degrade the contact surfaces. As the connection deteriorates, resistance and heat can rise together, giving maintenance teams a reason to investigate a sustained temperature increase under comparable loads.

Can You Monitor a PDU or MCC Without an Outage?

Yes. Once sensors are installed, you can review temperature readings while the PDU or MCC is operating and the enclosure stays closed. Plan sensor installation around a scheduled maintenance window, and have qualified personnel confirm the installation requirements for the equipment and follow the site’s electrical safety procedures.

Does Continuous Thermal Monitoring Replace IR Scans?

Continuous monitoring can satisfy certain thermal inspection requirements under NFPA 70B. IR scans survey surfaces visible to the camera, while permanent sensors track the points where they’re installed. How your facility applies it depends on the equipment, sensor coverage, and applicable maintenance requirements.

 

Attending Automation Fair 2026?

If you’re at Automation Fair November 17–19, stop by Booth 625 to see the GraceSense HSM 600 and talk with us about the connections you’re most concerned about. You can also download the CTM Readiness Checklist to start that conversation with your team and identify which assets you’d monitor first.

Stay SAFE, and have a GREAT week!

To safer, smarter operations,


connect with us